1.2.9. The car with universal remote radio management HomeLink

Universal remote radio management HomeLink can be programmed portable transmitters of already programmed devices.

Universal remote radio management HomeLink gives convenient possibility, without leaving the car, to use various devices, for example, garage collars, safety systems, house illumination etc.

Universal remote radio management HomeLink allows to replace three various portable transmitters of corresponding devices with one (universal remote radio management). Mechanisms of garage and external gate more often concern such devices. Programming of portable transmitters on the user remote radio management is carried out by the block of management located near a forward bumper on the right.

For management possibility various devices by means of universal remote radio management HomeLink it is necessary to program the corresponding transmitter preliminary. If after the first programming of the device do not function, the given devices should be checked up on presence of a changeable code

ATTENTION At programming of universal remote radio management HomeLink be convinced of absence in a direct environment of people or subjects. Inadvertent inclusion in the course of programming of the mechanism of gate is fraught under certain circumstances with a jamming and by that травмированием or drawing of a damage to property.

Programming of universal remote radio management HomeLink is carried out located in a sun-protection peak of the driver by keys, and also the operated transmitter from outside a forward bumper.

Fig. 1.25. A sun-protection peak of the driver

Include ignition.

Fig. 1.24. Emergency unlocking of a cover of the refuelling hatch

Press both extreme keys of universal remote control HomeLink (fig. 1.24) yet will not start to blink a light-emitting diode (approximately through 20). Thereby there is a removal of all data which has been saved up in memory of system.

Press a key HomeLink which is necessary for programming.

Keep a key pressed and wait, while the light-emitting diode will start to blink. After that the five-minute stage of programming of module "HomeLink" begins. The slow blinking testifies To it after release keys.

Leave the car and become before it with an original portable transmitter of a drive of garage gate or other device on which the key HomeLink is programmed.

Keep an original portable transmitter of the device subject to programming on removal about 0–30 sm under the right forward headlight at a car bumper.

Press a key of inclusion of an original portable transmitter.

At the included function of a portable transmitter observe of indexes of turn of the car. The positive result of programming HomeLink proves to be true a triple blinking of system of the emergency light alarm system.

In the absence of a triple blinking of lanterns repeat programming process on other removal from a bumper.

The necessary distance between a portable transmitter and module "HomeLink" located in a bumper is defined by the device which is necessary for programming. Probably for programming some attempts is required.

Excess of a five-minute stage of programming proves to be true a unitary blinking of system of the emergency light alarm system. In this case it is necessary to repeat programming. For this purpose repeat programming process from outside a sun-protection peak.

At programming of two other keys be guided by the above-stated description.

If after positive programming, nevertheless, keys HomeLink do not possible to open garage gate or other devices there is a probability of functioning of concrete system with a changeable code. In this case additional programming of a changeable code is necessary

Some devices demand additional programming of a changeable code of universal remote radio management HomeLink.

Again press and keep pressed a key HomeLink which already programmed earlier.

Observe of a light-emitting diode HomeLink. If the diode quickly blinks in the beginning, and through 2 with burns continuously it means presence of a changeable code of the corresponding device, for example, devices for opening of garage gate.

Inclusion of function of the mechanism of the electric motor of the device for opening of garage gate

Find a key of adjustment of the mechanism of the electric motor of the device for opening of garage gate. The exact site and colour of a key depends on mark of the manufacturer of the device.

Press a key of adjustment of the mechanism of the electric motor of the device for opening of garage gate (thus the light-emitting diode of "adjustment" of the mechanism of the electric motor, as a rule, burns). Now at your order nearby 30 with for realisation of programming of the key located in a sun-protection peak HomeLink.

Again press and release a key HomeLink which already was programmed earlier.

For end of programming of a changeable code again press a key HomeLink.

After programming by a key of a sun-protection peak the device for opening of garage gate should distinguish a signal HomeLink and open gate after key pressing HomeLink. If necessary now it is possible to program other keys.

THE NOTE In the presence of the assistant process of programming of a changeable code can be simplified and accelerated. For end of process of adjustment of some devices for opening of garage gate it is necessary to press the third time a key HomeLink. In case of difficulties of programming of a changeable code studying of the operation manual on the device for opening of garage gate or other device probably will help.

Using the programmed devices is carried out located in a sun-protection peak of the driver by keys HomeLink.

Include ignition.

Press the programmed key HomeLink. There is a management of the device programmed on a given key (for example, the device for opening of garage gate).

During a manipulation with command keys the light-emitting diode HomeLink burns.

Both extreme command keys probably to carry out dump of all programmed даннных HomeLink.

For this purpose include ignition.

Press both extreme keys, the light-emitting diode yet will not start to blink.

Release keys.

After dump of the data of programming of keys of universal remote radio management HomeLink the device again is in a mode of adjustment and is ready to new programming.

THE NOTE Separate dump of the programmed keys is impossible. For the safety reasons it is recommended to carry out dump of the programmed keys HomeLink before car sale.

There is a possibility of reprogramming of one key HomeLink without change of the programmed positions of other keys.

Press an actual key HomeLink, slowly the light-emitting diode yet will not start to blink.

Keep an original portable transmitter of a drive of garage gate or other device on removal about 0–30 sm under the right forward headlight at a car bumper. The necessary distance is defined by the device which is necessary for programming.

Press a key of inclusion of an original portable transmitter of the device for opening of garage gate or other device.

At the included function of a portable transmitter observe of indexes of turn of the car. The positive result of programming HomeLink proves to be true a triple blinking of system of the emergency light alarm system.

In the absence of a triple blinking of lanterns repeat programming process on other removal from a bumper.

After a triple blinking of the emergency light alarm system there is a dump before the programmed data HomeLink and the new device is programmed. For using the new device press the programmed key HomeLink.

THE NOTE For programming some attempts probably is required. Duration of process of each stage of adjustment should make a minimum 15 with. Only after that it is possible to pass to other stage. Observe thus of lanterns of indexes of turn.